Tanks Inc MU-HT-KIT6 EFI Gas Tank Kit Ford/Mercury 1964-1968
MU-HT-KIT6 EFI Gas Tank Kit Ford Mustang 1964-1968, Mercury Cougar 1967-1968
EFI Gas Tank Kit includes:
-
16 gallon Tank
-
400 LPH Pump
-
73-10 Ohms Sending Unit
INJECT YOUR CLASSIC HOTROD!!
Tanks, Inc. carries a wide veriety of fuel injection ready tanks with built in trays and appropriate fittings. These are original-fit tanks and require no modifications to mount.
This is the best choice for adding a fuel injection ready tank to your classic vehicle! Universal tanks are also available for totally custom applications.
Tanks Inc. now has EFI tanks for 1964-1968 Ford Mustang, 1967-1968 Mercury Cougar. These powder coated tanks have the internal baffling necessary for today's EFI engines.
Tanks has you covered for your next EFI swap.
TANKS, INC. has been a leader in the street rod industry, receiving various awards for safety and innovation. In addition, it was the first to introduce style into street rod gas tanks; radiused edges, die-stamped openings, flush-mounted fittings, indented panels and slotted mounting flanges, just to name a few.
This notched corner tank is perfect for mini-tub applications. Both corners are notched 7" in and 7" back for better tire and exhaust clearance. The rear of the tank is the stock depth while the front of the tank is 1" deeper than stock. This additional rake of the gas tank provides better fuel delivery to the pump.
- Fits: 1964-1968 Ford Mustang
- Fits: 1967-1968 Mercury Cougar
- Fuel Injection Ready!
- EFI style internal baffling with extra large 4.8 liter dual tube baffled fuel tray to prevent fuel pump starvation.
- 16 Gallon.
- Uses our GPA-6 series fuel pumps.
- 32-3/4" x 24-1/2" x 7-1/2"
- Designed to use our GPA 6 In Tank Fuel Pump Module
- TAN-ORG -73-10 Ohms ranges available to work with factory or aftermarket gauges.
- MU-T Pictured with Billet Cap and Neck
- In-Tank Fuel Pump Module - GPA-6 Series
- Made in the USA
- Heavy 10 gauge no-warp mounting plate
- 1/4" NPT Supply and Return Line
- Barbed Vent Fitting
- Oven brazed fittings
- Up to 100 PSI
- In-tank wire harness
- Genuine Walbro Fuel Pump
The GPA-6 Series Fuel Pump Module is designed to be used in many of our die-stamped alloy-coated and stainless steel gas tanks that have factory-installed reservoir trays. The tray is an absolute necessity for fuel-injection in order to prevent fuel starvation when accelerating and cornering.
We use Walbro high-performance pumps in all of our fuel injection modules, and we offer four different operating ranges in order to supply up to approximately 1000 horsepower. The internal wiring harness, supply line, return line, filter sock and insulator sleeve are included. (The gasket and screws with o-rings are not included with the pump because we include gaskets and screws with our tanks.)
The heavy 10-gauge no-warp mounting plate contains fittings for the supply, the return, the vent and the electrical connector. It is yellow-zinc plated to prevent corrosion.
5 Bolt Fuel Sending Unit
Our fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground they work on all 6-24 volt systems positive or negative ground. They do not have a fuel pickup tube built into them as some original senders may have. Made with a high quality ceramic board rheostat.
Application Listing:
- ORG - Early Ford & Mopar - 73-10 Ohms
The first number of the (Ohms) represents empty and the following is for full.
year make model | 1964-1968 Ford Mustang and 1967-1968 Mercury Cougar |
---|---|
Manufacturer | TANKS INC. |
More Info | This is a kit and is sold "as is" no substitutions |