Tanks Inc. 32P Ford 1932 Poly Fuel Tank
Tanks Inc. 32P Ford 1932 Poly Fuel Tank
1932 Ford Poly Fuel Tank with Fiberglass Cover
32P Size is: 14 Gallon Capacity - 1-7/8" Deeper Than Stock
INJECT YOUR CLASSIC HOTROD!!
Tanks, Inc. carries a wide veriety of fuel injection ready tanks with built in trays and appropriate fittings. These are original-fit tanks and require no modifications to mount.
This is the best choice for adding a fuel injection ready tank to your classic vehicle! Universal tanks are also available for totally custom applications.
Tanks Inc. now has EFI tanks. These powder coated tanks have the internal baffling necessary for today's EFI engines. With fuel pump options to supply up to 1000 horsepower!
Tanks has you covered for your next EFI swap
This Is A Carbureted Tank That Can Be Converted To Fuel Injection Tank By Adding the Fuel Pump Kit Below
TANKS, INC. has been a leader in the street rod industry, receiving various awards for safety and innovation. In addition, it was the first to introduce style into street rod gas tanks; radiused edges, die-stamped openings, flush-mounted fittings, indented panels and slotted mounting flanges, just to name a few.
It was also the first on the block with a true reproduction Deuce tank, though many had tried and failed.
Their exclusive "Baffle-Tunnel" made polyethylene gas tanks a viable choice for the rodder. To top it off, the company
- High-Density Seamless Polyethylene - Heavy Wall Construction
- Bolts Into Frame, the fiberglass cover bolts to the top of the rails and the tank bolts to the bottom of the frame rails
- Patented Baffle - Tunnel - Minimizes Sloshing
- Top Mounted Pickup Tube & Vent
- Bolt-on Steel Neck and Billet Cap
- Paintable Fiberglass Cover and Filler Neck
- (Does Not Allow In-Tank Fuel Injection Pump Installation)
- 14 Gallon Capacity - 1-7/8" Deeper Than Stock
- Accepts All 5-Hole Senders - VDO, SW, Classic, etc.
- Leak Tested
- Remote Rollover Vent Valve
|
In-Tank Fuel Pump Module-GPA-Series
From Tanks, Inc.- Made in the USA
- Heavy 10 gauge no-warp mounting plate
- 1/4" NPT Supply and Return Line
- Barbed Vent Fitting
- Oven brazed fittings
- 40-100 PSI
- In-tank wire harness
- Genuine Walbro Fuel Pumps
-
Pump Flow Rates:
TBI 109 Liter Per Hour Pump
- 29 GPH @ 12 PSI
PA-2 Deluxe 190 Liter Per Hour Pump
- 54 GPH @ 40 PSI
- 50 GPH @ 50 PSI
- 48 GPH @ 60 PSI
PA-4 High Flow 250 Liter Per Hour Pump
- 68 GPH @ 40 PSI
- 65 GPH @ 50 PSI
- 62 GPH @ 60 PSI
PA-6 High Performance 400Liter Per Hour Pump (500 - 1000 Horsepower)
- 106 GPH @ 40 PSI
- 99 GPH @ 50 PSI
- 91 GPH @ 60 PSI
NOTE: All Flow Rates Are At 13.5 Volts
The GPA-Series Fuel Pump Module is designed to be used in many of our die-stamped alloy-coated and stainless steel gas tanks that have factory-installed reservoir trays. The tray is an absolute necessity for fuel-injection in order to prevent fuel starvation when accelerating and cornering.
We use Walbro high-performance pumps in all of our fuel injection modules, and we offer four different operating ranges in order to supply up to approximately 1000 horsepower. The internal wiring harness, supply line, return line, filter sock and insulator sleeve are included. (The gasket and screws with o-rings are not included with the pump because we include gaskets and screws with our tanks.)
The heavy 10-gauge no-warp mounting plate contains fittings for the supply, the return, the vent and the electrical connector. It is yellow-zinc plated to prevent corrosion.
year make model | 1932 Ford |
---|---|
Manufacturer | TANKS INC. |